QUAD 4 x4 Your 4x4 Experts!
23 Turner Rd., Roberts, Montana 59070
 CALL  406-446-2427 • Order 24 hours a day.  7 days a week.

COMMON DANA SPICER AXLE AND DIFFERENTIAL PARTS

Dana-Spicer Drive Axles are found many Chevy, Dodge, Ford, GMC, IHC, and Jeep vehicles from the 1940's to current. Many of these axles share common parts.  This page includes general applications and pricing for various Dana-Spicer front and rear axles including Models 30, 44, 50,  60, 61, 70, 80.  For Specific Application Information, use the Link Bar Above or at the end of the application information to see our Axle Page for your vehicle and axle!  

See Our What's New Web Page

Pinion Yoke Kits  Each Kit includes new pinion yoke, pinion seal, pinion nut, pinion washer, u-joint retaining hardware,  Threadlocker, and instructions.  Made in U.S.A. 




 

Power-Lok™ Rebuild Kits   Is your factory Power-Lok™ limited slip rear axle chattering or slipping?  Chances are the original clutch packs are worn out.  Rebuild your factory limited-slip differential with genuine Dana-Spicer replacement parts.  Each kit includes complete clutch pack, 8 oz. of limited slip additive, axle shaft flange gaskets, Threadlocker, RTV sealant, and instructions.  Made in U.S.A.   Can Not Be Air Shipped! Must Be Shipped UPS Ground or Surface Mail!
 

QK4604 Dana 70 Powr-Lok Kit $119.97

QK4608 Dana 80 1994-1999 $229.97

Also available:  Complete Dana 80 Differential Parts Kit for Dana 80.  Includes all internal P/Lok components including clutches, 2 side gears, 4 pinion-mate gears, 2 cross-shafts, and thrust washers.

All Others..................................................CALL

Differential Bearing Kits are genuine Dana-Spicer replacement parts.  Most numbers feature Timken bearings.  Differential bearing replacement is recommended every 125,000-150,000 miles.  Each kit includes two bearings, two bearing cups, and differential adjusting shims. Usually Made in U.S.A. or Canada, but bearings may sourced from other countries.
 

QK4606 Dana 60, 70 Diff Bearing Kit $94.97

QK4605 Dana 44 Differential Bearing Kit with shims

Pinion Bearing Kits are genuine Dana-Spicer replacement parts.  Most numbers feature Timken bearings.  Pinion bearing replacement is recommended every 125,000-150,000 miles.  Each kit includes two bearings, two bearing cups, pinion depth shims, pinion preload shims, pinion seal, pinion washer, and pinion nut.  Usually Made in U.S.A. or Canada, but bearings may sourced from other countries.

5 pound Dead-Blow Hammer is one of the handiest tools you will ever own for working on your Dodge 4x4 truck.  Indispensable any time a part needs a little persuasion.  Plastic face will not ding or damage critical components such as differentials.  You might be able to wear one of these out, but in 30 years of professional service work, Dan the Gear Man  has yet to wear his out!
To Order, go to the 4x4 Tools Page  Made in U.S.A.

Use to relieve bearing preload on your Dana Front and Rear Axles and C205F Corporate Axles.  1994-2002 Dodge applications include:

1994-2002 All 1500, 2500, 3500 Front Drive Axles (Dana 44, 60)
1994-2002 All 2500 and 3500 Rear Drive Axles (Dana 60, 70, 80)

Also use on many other Dodge, Jeep, Ford, GM, and International applications from 1941 to current.

To Order, go to the 4x4 Tools Page  Made in U.S.A.