|
Special Service Tools For Your
Jeep® |
|
|
|
|
|
Maintain and repair your Jeep®
vehicle with the right tool for the job. Whether you are a
shade tree mechanic or a top notch professional automotive
technician, you will find our ever expanding selection of 4x4
service tools has the hard to find tools you need to keep your
Jeep® SUV or truck in peak
operating condition! For general service tools or
tools to service a competitive brand of 4x4's,
click on the appropriate link above. PAGE IS STILL UNDER
CONSTRUCTION! |
|
 |
Visit Our
Ball Joint Press Tools Page for Ball Joint Press Sets and
Individual Tools |
QT1089
Inner Axle Seal Installer |
Inner Axle Seal Installers make
installing those hard to reach front inner axle shaft seals easy
without damaging the seal! Can be used with slide hammers,
pulling screws, driver handles, or hammers. Made in U.S.A.
To order any of the installers listed below, please see our
Front Axle
Shaft Seal Tools Webpage.
Cherokee Wide Track: 1978-1985
J10, J20 Truck: 1978-1987 |
T1029
or
T1084 |
Cherokee, Wagoneer: 1974-1977
J10, J20 Truck: 1974-1977 |
T1041
or
T1165 |
| CJ: 1972-1977 |
T1079 |
Right Side Seal with
Central Axle Disconnect:
Cherokee, Comanche (XJ) 1987-1991
Wrangler (YJ): 1987-1996 |
T1080 |
Left Side Seal with
Central Axle Disconnect :
Cherokee, Comanche (XJ) 1987-1991
Wrangler (YJ): 1987-1996 |
T1089 |
CJ: 1978-1986
Following Applications are for Jeeps without Central
Axle Disconnect:
Cherokee/Comanche (XJ),
Wrangler (TJ, YJ), Grand Cherokee, small Wagoneer,
Grand Cherokee (ZJ): ALL 1984-2002 |
T1139 |
|
Call us for
Installers for other Jeep applications |
QT1079 Installs the Left
Axle Seal on 1984-96 Jeep Front Axles with vacuum
controlled Central Axle Disconnect (CAD) on Jeep
Cherokee (XJ) and Wrangler (YJ) models or BOTH left and
right seals on CJ's and XJ/YJ models without CAD.
$55
Please Note: This
Installer ONLY works with CR Seals |
SOLD OUT! |
|
QT1080
Right Side Inner Axle Seal Installer for 1984-96 Jeep
Front Axles with vacuum controlled Central Axle
Disconnect (CAD) on Jeep Cherokee (XJ) and Wrangler (YJ)
models. The passenger side axle shaft seals on
these models are almost impossible to install without
our installation tools. $55
Please Note: This
Installer ONLY works with NOK made Jeep Original
Equipment Seal p/n: 83503504 |
|
QT1089
Installs the Left Axle Seal on 1984-96 Jeep Front Axles
with vacuum controlled Central Axle Disconnect (CAD) on
Jeep Cherokee (XJ) and Wrangler (YJ) models or BOTH left
and right seals on CJ's and XJ/YJ models without CAD.
$55
Please Note: This
Installer ONLY works with NOK made Jeep Original
Equipment Seal |
|
|
|
 |
2-1/16" Hex Front Spindle Nut Socket for 1946-1986
Jeep CJ-5, CJ-6, CJ-7, and CJ-8 (Scrambler) and most other Jeep vehicles from 1942-1971
except M715 series. This Special Thinwall 1/2"
drive socket is an absolute necessity to properly
service the front wheel bearings on your vintage Jeep.
Also fits IHC Scout. Made in U.S.A. QT1011
$29.97Out of Stock. |
|
 |
Hex Spindle Nut Socket for 1967-1969
Jeep M715, M725, and M726 1¼ ton Military
Trucks. Special
thin-wall 2.5" hex socket
fits both
Front & Rear Spindle Nuts. 1/2" Drive.
Made in U.S.A. QT1013 $31.50 |
|
| |
|
|
| |
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| |
4 Prong Spindle Nut Socket fits 1989 Jeep
Fullsize Cherokee, Wagoneer/Grand Wagoneer, J10 & J20 trucks |
| |
Rounded Hex Rear Spindle Nut Socket for J20
|
| |
Spindle Puller attachment fits |
 |
Bearing Cup Installers
Install those critically important and expensive bearing cups
without damaging the precision machined bearing surfaces.
Faster, safer, and easier than using a punch. Use in combination
with one of our Driver Handles. Order Cup Installers from
our
Bearing Cup Installer Page |
 |
Wheel Seal Installers
Quit wrecking those wheel seals with a hammer! QuadTool™
Standard & Pro Duty Wheel Seal Installers are precision machined
for specific wheel seal applications. Use our inexpensive high
impact plastic Standard Duty installers for occasional
use. Choose our aluminum Pro Duty installers for frequent
seal installation |
| |
Ball Joint Installer |
| |
Ball Joint Socket |
| |
Tie Rod Separator |
 |
Installer Driver Handles
For use with a variety of QuadTool™
Seal and Bearing Installers. Made in U.S.A..
Order from our
4x4 Tools page
QT1100 8" Handle for general purpose use
QT1101 14" Handle for axles and
transmissions
QT1102 47" Handle for inner axle
seals |
 |
Borg Warner T18,
T19, & T98 Transmission Dummy Shaft is used to hold the
counter shaft needle bearings, spacers, sleeve, and thrust
washers in place when servicing Borg Warner T18, T19, & T98 four
speed transmissions found on many 1950's to 1980's Ford, IHC,
and Jeep vehicles. Made in U.S.A.
QT2031 Order from our 4x4 Tools page |
 |
Pinion Bearing Installers Quickly and easily install inner
pinion bearings without damaging the bearing or pinion. Made in U.S.A
QT1003 Dana Model 70
Order from our 4x4
Tools page |
  |
Step Plates are used
when pulling and/or installing your differential bearings.
These plates fit in the axle shaft hole of your differential.
Use as a push plate for bearing removal or to support the
differential when pressing on new bearings. Made in U.S.A.
Order from our 4x4 Tools page
QT1034
fits Mod 60-70-80, Ford 10.25" and GM 14 bolt
QT1035
fits Model 44 axles
QT1036
fits Ford 9" axles
|
 |
|
 |
|
 |
|
