QU11119 D70 SRW Hub and Brake Drum Assy

photo

QU11119 Dodge Dana 70 Single Rear Wheel Hub and Brake Drum Assembly with eight 1/2" wheel studs for all 1986-1993 D250, W250, D350, and W350  Single Rear Wheel (SRW) Dodge Ram trucks  that have 1/2" wheel studs, 6-5/16" wide, inboard mounted brake drums, and either 12" x 2.5" or 12" x 3" rear brake shoes, is a genuine factory assembled, original equipment rear hub and drum assembly that includes the wheel bearing cups. Made in U.S.A.

Also See QU11288U Used Hub

QU11119 Hub and Drum Assembly

tech note

Dan the Gear Man® Tech Note 1:
QU11119 Rear Hub and Drum assembly is identical to the original hub and drum your truck was built with except that it does not have the sheet steel oil guard that fits over the back part of the hub. The oil guard is no longer available.

tech note


Dan the Gear Man® Tech Note 2:
The brake drum has an inside brake surface width of 3-1/2" and the approximate overall width of the brake drum (which is mounted against the inboard face of the wheel hub) is 6-5/16".  Bolt circle for mounting wheels is 6-1/2". QU11119 Hub/Drum assembly will NOT fit Dodge 3/4 ton or 1 ton SRW trucks that use hub/drum assemblies with 4-1/2" wide, outboard mounted brake drums.

tech note

Dan the Gear Man® Tech Note 3:
Up until at least mid 1990, Dodge used wheel hubs manufactured by Budd for Dana 70 and high capacity Dana 60 full floating rear axles. Later hubs were made by Bosch. The Budd hubs can be identified by the number 97465 cast on the back side of the hub flange. The number may be all together or separated by a wheel bolt hole. Also, the outboard side of the Budd hub is smaller in diameter next to the hub flange and larger at the outboard end. In contrast, the outside diameter of the outboard side of Bosch supplied hubs are machined to the same diameter from the hub flange out. The Bosch and Budd type hubs are interchangeable even though they look different externally. 

tech note

Dan the Gear Man® Tech Note 4:
QU11119 Wheel hubs and drums are from Dodge Dana 60, Dana 60HD, or Dana 70 rear axles rated at 6200 pounds or higher. The inner wheel bearing/bearing cup are larger than the outer wheel bearing and cup. These hubs will NOT fit the more common 5500 pound and 5800 pound rated Dana 60 rear axles typically found in Dodge 3/4 ton trucks.

tech note

Dan the Gear Man® Tech Note 5:
Depending upon the year and model, Dodge used different brake drums and wheel studs  with QU11119 hubs. Both 1/2" and 5/8" wheel studs were used over the years. The knurl diameter of both sizes of studs is the same. D and W series trucks used 12" brake drums that have an overall width of about 6-1/2". B series vans have 5" wide drums. Brake shoe size was usually 12"x3", but some older trucks were built with 2-1/2" wide brake shoes.

tech note

Dan the Gear Man® Tech Note 6:
Most if not all Dodge rear axles up to mid 1990 that use QU11119 hub use studs and split tapered cones for axle shaft retention. Axlse built from mid 1990 to 1993 used grade 9 hardened bolts to secure the axle shafts to the hub.

tech note

Dan the Gear Man® Tech Note 7:
Matching Parts for QU11119 Hub and Drum Assy:
QU11119 Hub and Drum Assembly
QU40450 Wheel Seal
QU50414 Inner Wheel Bearing
QU50413 Inner Wheel Bearing Race
QU50412 Outer Wheel Bearing
QU50411 Outer Wheel Bearing Cup
QU40078 Steel Axle Shaft Flange Gasket
QU40577 Split Tapered Axle Shaft Bushing for 1972-1990
QU95036 7/16" SAE All Metal Locknut
QU40535 Axle Shaft to Wheel Hub Bolt
QU40077 Stock Spindle Nut for 1979-1993
QU40089 Stock Spindle Nut Lock for 1979-1993
QK4013 Stock Spindle Nut Kit for 1979-1993
QU90018 Pyroplex Plus Synthethic Wheel Bearing Grease 
QT1801 Outer Wheel Bearing Cup Installer
QT1804 Inner Wheel Bearing Cup Installer
QT1500 Rear Wheel Seal Installer
QT1100 Driver Handle for Wheel Seal Installer
QT5500 Wheel Bearing Packer

tech note

Dan the Gear Man® Tech Note 8:
1972-1993 Dodge Factory Service Manuals on CD
are your source for complete service, maintenance, and overhaul information for your 1972-1993 Dodge Ram truck. Our Chrysler authorized reproduction Factory Shop Manuals cover almost everything you may need to service on your big Ram truck from alternator testing to wheel bearing replacement. Dodge Factory Manuals include hundreds of black and white illustrations, service procedures, torque specifications, wiring diagrams, and troubleshooting charts. 1972-1993 Dodge Ram Factory Shop Manuals include coverage of axles, body, brakes, clutch, drive shaft, engine, electrical, exhaust, frame, transfer case, transmission, steering, and suspension. 
1972-1988 Dodge Factory Service Manuals on CD Catalog Page
1989-1993 Dodge Factory Service Manuals on CD Catalog Page

Application

Dodge:
1972-1980 D200, W200 with optional 6200 Pound Rated Dana 60, Dana 60HD Rear Axle
1972-1980 D300, W300 with Single Rear Wheels
1981-1993 D250, W250 with optional 6200 Pound Rated Dana 60, Dana 60HD Rear Axle
1989-1993 D250, W250 with Cummins Diesel Engine
1981-1993 D350, W350 with Single Rear Wheels
1974-1990 B300, B350 Van with 9000 pound GVW