Parts for Dana-Spicer Model 50 IFS Front Axles in 1983-1997 Ford F-250, F-350 4x4 Trucks
Page is under Construction more parts to be added soon!
We stock a good selection of replacement parts for 1983.5 to 1997 Ford F-250 and 1983.5-1985.5 Ford F350 4x4 trucks with Dana Spicer Model 50 Independent Front Suspension (IFS) Twin Traction Beam® drive axles. First used in 1980, the Ford IFS Twin Traction Beam® Dana 50 axle went through a significant differential and right side inner axle shaft design changes for vehicles built in 1983 starting with Dana Axle Bill of Material number 610170 (Ford Axle Codes E2TA-DA, E2TA-HA, E3TA-HFA). The exact date of change is not listed in Fords parts books, however 1983 is the only model year that vehicles with either axle design were manufactured.
Axle Identification
Ford was the only vehicle manufacturer to use Dana Twin Traction Beam® Independent Front Suspension Axles which can be found on 1980-1997 model year Ford 4x4s. The Twin Traction Beam® IFS Axle line includes the coil spring Models 28 and 35 found in Bronco II, Explorers and Ranger pickups, the Model 44 which was used in fill size Broncos, F-150 (coil springs), and light duty F-250 pickups (leaf springs), and the leaf sprung 4500 to 4600 pound rated Model 50IFS axle in heavy GVW F-250 and 1980-1985.5 F-350 trucks. Link to Our Ford Web Page Index
Hub Size: Ford used both Dana 44 and Dana 50 IFS Twin Traction Beam® Front Axles in F-250 trucks. The easiest way to tell them apart is by measuring the diameter of the wheel hub or locking hub. Dana 44 axles have hubs that are approximately 3-3/8" in diameter. Dana 50 Hubs are about 4-1/8" in diameter.  
  Right Differential Output Shaft: The major difference between 1980-1983.5 and 1983.5-1997 Ford Dana 50IFS front axles is the way the right differential output shaft is supported and retained. The early axles use a pressed-on taper roller bearing and an external bolt-on retaining flange. Later production axles use a straight roller bearing pressed into the differential housing and the axle shaft is retained by a snap ring inside the differential next to the differential side gear. The early right diff output shafts could be pulled without removing the differential housing from the axle beam with a special slide hammer puller attachment, but seal replacement also requires the bearing be replaced. For later axles, you MUST remove the differential housing from the axle beam to access the snap ring, but once it is out replacing the right seal is quick and easy.  
  Suspension: Leaf spring  
  Knuckle Mounting: Ball Joints  
  Wheel Hub: 1983-1997 Ford Model 50 axles have an internally splined hub in which a splined lockout hub assembly would fits into.  
     
Check Out Now
Axle Assemblies and Axle Housings
     
  This Section under construction.  
     
     
     
Check Out Now
Axle Shafts
We still have brand new left and right Axle Shaft assemblies in stock for 1983-1997 Ford 4x4s with Dana 50 IFS Front Axle. Production on these shafts ended years ago, so when our current limited inventory is exhausted that will be the end of new assemblies. Our available used axle shaft inventory is also limited due to the Cash for Clunkers program and high scrap prices which has sent large numbers of 1983-1997 Fords with Dana 50 axles straight to the crusher. Link to Our Ford Web Page Index
QK4773 Left Axle Shaft Assembly for all 1983 to 1997 Ford F-250 and 1983-1985 Ford F-350 4x4 trucks equipped with the Dana 50 IFS Twin Traction Beam® Front Axle. Assembled in U.S.A. of U.S.A. and Mexico Parts

Please refer to QK4773 page for more details and ordering information.
QK4774 Right Axle Shaft Assembly for all 1983 to 1997 Ford F-250 and 1983-1985 Ford F-350 4x4 trucks equipped with the Dana 50 IFS Twin Traction Beam® Front Axle. Assembled in U.S.A. of U.S.A. and Mexico Parts

Please refer to QK4774 page for more details and ordering information.
  QU40571 Dana 50IFS Right Differential Output Shaft for all 1983 to 1997 Ford F-250 and 1983-1985 Ford F-350 4x4 trucks equipped with the Dana 50 IFS Twin Traction Beam® Front Axle.
QU40815 Dana 50IFS Right Axle Shaft Slip Yoke for all 1983 to 1997 Ford F-250 and 1983-1985 Ford F-350 4x4 trucks equipped with the Dana 50 IFS Twin Traction Beam® Front Axle.
Check Out Now
Axle Shaft Boots and Seals For Inner Axle Shafts
Ford introduced a redesigned Dana 50IFS Twin Traction Beam Front Axle during the 1983 model year that uses a right Differential Output Shaft retained by a C-Clip inside the axle housing. The new design requires the Differential Housing be removed from the left axle beam to service the Right Axle Shaft Seal and/or center axle universal joint. Also introduced was a right Axle Slip Joint protected by a flexible rubber Boot instead of a pressed on Yoke Seal. The Slip Yoke Boot eliminated one of the chronic problems the previous 1980-early 1983 axle had, namely axle shaft spline failure from water and grit infiltrating past the seal. Link to Our Ford Web Page Index
QU40087 Left Ford Dana 50 IFS Axle Shaft Seal fits all 1983-1997 Ford F-250 and 1983-1985.5 F-350 4x4 trucks with Dana 50 Twin Traction Beam® IFS front axles.
QU40088 Right Ford Dana IFS Axle Shaft Seal fits all 1983-1997 Ford F-250 and 1983-1985.5 F-350 4x4 trucks with Dana 50 Twin Traction Beam® IFS front axles that have the right inner axle shaft retained by a snap ring.
QU40557 Axle Shaft Slip Yoke Seal for Ford Dana 50IFS Twin Traction Beam® Front Axles is a genuine original equipment part for all 1983.5-1997 Ford Dana 50 IFS Twin Traction Beam® front axles in 1983.5-1997 F-250 and 1983.5-1985.5 F-350 Ford 4x4s.
QU40572 Ford Dana 50IFS Right Axle Shaft Slip Yoke Boot is a genuine original equipment replacement Boot for all 1983-1997 Ford F-250 and 1983-1985.5 F-350 4x4 Trucks with Dana 50 Twin Traction Beam® IFS front axles that have the right inner axle shaft retained by a snap ring.

QU40085 One Ear Stainless Steel Boot Clamp for the small end of QU40572 Slip Yoke Boot

 
QU40084 One Ear Stainless Steel Boot Clamp for the large end of QU40572 Slip Yoke Boot
Check Out Now
Axle Shaft Seals and Seal Kits for 1993-1997 Outer Axle Shafts
The dead, hollow spindle design of the 1993-1997 era Ford Dana 50 IFS axles use QU40149 needle bearing to support the outer axle shaft. Axial thrust is handled by a combination thrust washer/spindle bearing seal. One Cup Seal is used to protect the spindle bearing. We stock all the individual components, plus Kits combining the pieces.
For 1983-1992 Model Years, See our Spindle Seal and Bearing Section for Outer Axle Shaft Slingers, Thrust Washers, and Axle/Spindle Grease Seals		 Link to Our Ford Web Page Index
QU40243 Outer Axle Shaft to Spindle Seal for 1993-1997 Ford F-250 is a genuine original equipment Seal that presses on your Ford 1993-1997 F-250,outer axle shaft next to the yoke. The lip of the seal rides against your spindle.
QU40496 Ford Dana 50 IFS Unitized Inner Spindle Seal and Thrust washer is a genuine original equipment unitized spindle seal and thrust washer used on 1993-1997 Ford F-250 4x4s with the Dana 50 IFS Twin Traction Beam front axle.
QU40372 Ford Dana 50 IFS Unitized Spindle Seal, Bearing and Thrust Washer Kit is a genuine original equipment Spindle Bearing, Spindle Seal and Spindle Thrust Washer set for 1993-1997 Ford F-250 4x4s with the Dana 50 IFS Twin Traction Beam front axle
QU40149 1993-1997 Ford Dana 50 Spindle Bearing is a genuine Dana Spicer original equipment part that is a press fit in the back of the spindle. This bearing is the primary support for your outer axle shaft.
Check Out Now
Axle Universal Joints
The Dana 50 IFS axle has 3 axle universal joints, one for the left side and two for the right side. For the 460 gas engine and later diesel trucks, this size u-joint is a bit on the small size. For the Dana 50, we offer QK4874 Greaseable U-joint as an inexpensive alternative to our QU40470 solid cross original equipment, non-greaseable u-joint which is our as our maximum strength option for these axles. QK4874 Greaseable U-joint is a whole lot cheaper compared to QU40470, but there is some strength loss since it is cross-drilled for grease passage. Link to Our Ford Web Page Index
QK4874 Greaseable External Snap Ring Axle Universal Joint for 1983-1997 Ford Dana 50 Front Axles in 4x4 F-250 and F-350 trucks with Dana 50IFS Twin Traction Beam® IFS front axles.
QU40470 Axle Shaft Universal Joint for 1983-1997 Ford Dana 50 Front Axles is an original equipment replacement, factory lubed, non-greaseable, external snap ring u-joint 1980 to 1997 Ford Dana 50 Twin Traction Beam® IFS front axles which were available on F-250 trucks for all years, plus 1980 to early 1985 F-350s.
Check Out Now
Ball Joints
     
  This Section Under Construction  
     
Check Out Now
Brake Parts
Our stock of Ford Dana 50 front brake parts is limited. For the most part, the front brakes generally gave pretty good service that was comparable to the contemporary Dodge and GM 4x4's with one exception. We saw a lot higher percentage of Fords with warped or cracked brake rotors compared to the competition. Whether this was due to the somewhat thinner Ford brake rotor thickness or our Ford customers were harder on their brakes, I can't say, but a F-250 or F-350 that was used to frequently tow a trailer always seemed to need rotors.
Link to Our Ford Web Page Index
  This Section Under Construction  
     
     
     
     
     
Check Out Now
Differential and Pinion Bearings (Individual)
If you only need a bearing or two for your 1983-1997 Ford Dana 50IFS diff, we stock the best: Timken®. For the amount of work it takes to change most axle bearings, the extra cost for a Timken® diff or pinion bearing is a small price to pay for better steel, more uniform surface finish, and accurate, precision ground races.
Link to Our Ford Web Page Index

QU50533 Ford Dana 50 Timken® Outer Pinion Bearing Cup

 

QU50534 Ford Dana 50 Timken® Outer Pinion Bearing

 

QU50539 Ford Dana 50 Timken® Inner Pinion Bearing Cup

 

QU50540 Ford Dana 50 Timken® Inner Pinion Bearing

 

QU50541 Ford Dana 50 Timken® Differential Side Bearing Cup

 

QU50542 Ford Dana 50 Timken® Differential Side Bearing

 
Check Out Now
Differential Bearing and Seal Kits
     
  This Section under construction  
     
     
Check Out Now
Differential Parts
  This Section still under construction  

QU40519 Differential Cross Shaft Lock Pin is a genuine Dana original equipment Roll Pin used to secure your differntal cross shaft to the diff case on 1983.5-1997 Ford F-250 and 1980-1985 Ford F-350 4x4 trucks with Dana 50IFS Front Axles.
QU40576 Dana 50IFS Pinion and Differential Shim Kit for 1983-1997 Ford F-250 and 1983-1985 Ford F-350 includes these genuine Dana parts: Pinion Depth Shims, Pinion Preload Shims, Differential Adjusting Shims, Axle Shaft Snap Ring, Pinion Nut and Pinion Washer.
     
     
     
     
     
Check Out Now
Gaskets and Gasket Makers
A cut gasket is not used between the differential housing and left axle beam on Dana 50 IFS axles because it's thickness would cause the inner axle shafts to be slightly misaligned with the center of the spindles. High quality RTV sealant is used. The mating faces of the diff housing and axle beam MUST BE Clean! That means NO dirt, fingerprints, old sealant, oil etc. on either mating surface. Link to Our Ford Web Page Index
S82194 Ultra Gray RTV Sealant combines high adhesion and resistance to both conventional and synthetic gear lubes. The perfect choice to seal the differential housing to the left axle beam on your Ford Dana 50 IFS Front Axle.
     
Check Out Now
Hubs and Hub Parts
We have limited stock on new original equipment Dana 50IFS Hub and Rotors. Ford used both manual and automatic hub locks for Dana 50IFS front axles. For Manual Hubs, we only stock parts for the 6 Bolt, Red or Black Dial (1983-1992) Warn built, factory plastic dial manual hubs. In 1993, Ford switched to a new manual hub style with a smaller grip, black plastic dial, which was superceded by a 3 bolt black plastic dial hub in 1995. We do not stock service parts for the 1993-1997 Ford factory black plastic dial manual hubs. Two versions of automatic hubs were used. We have no replacement parts for the 5 screw 1993-1994 auto hub, but we do have some small parts for the 1995-1997 auto hub with three screws. Link to Our Ford Web Page Index
QU20085 30 Spline Three Piece Axle Thrust Washer Set fits on the outer axle shaft splines between the spindle and axle shaft snap ring on many 1993-1997 axles.
  QU20223 Hub and Rotor for 1980-1987 Ford Dana-Spicer Model 50IFS Front Axles with single rear wheels and 1/2" wheel Studs.  
  QU20225 Hub and Rotor for 1988-1994 Ford Dana-Spicer Model 50IFS Front Axles with single rear wheels and 9/16" wheel Studs.
  QU20226 Hub and Rotor for 1995-1996 Ford Dana-Spicer Model 50IFS Front Axles with single rear wheels.
  Parts For 1995-1997 Automatic Lockout Hubs  
QU20201 Auto Hub Spindle Nut Retaining Clip for Ford Dana 50IFS Front Axles
QU20202 Screw, Auto Hub Cap for Ford Dana 50IFS Front Axles
QU20203 Auto Hub Decal for Ford Dana 50IFS Front Axles
QU20207 Body Retaining Snap Ring for Auto Hub on Ford Dana 50IFS Front Axles
QU20208 Axle Shaft Snap Ring for Auto Hub on Ford Dana 50IFS Front Axles
QU20209 Sealing O-Ring for Auto Hub Cap on Ford Dana 50IFS Front Axles
  Parts for Manual Lockout Hubs  
QU40155 Axle Shaft Snap Ring fits in the groove machined at the end of the outer axle shaft splines in Ford Dana 50IFS Front Axles.
QU40150 Lockout Hub to Wheel Hub Snap Ring for Warn® Spline Mount Hubs used in Ford Dana 50IFS Front Axles.
QU50116 Cap QUAD-Ring square cross section sealing ring for Factory Warn® Spline Mount Hubs in Ford Dana 50IFS Front Axles.
QU50240 Dial O-Ring for Warn® Spline Mount Hub Dials in Ford Dana 50IFS Front Axles.
QU56013 Warn® Dial Assembly for Original Equipment Spline Mount Hubs used in Ford Dana 50IFS Front Axles.
QU56017 Warn® Spiral Retaining Ring for Current Production Spline Mount Replacement Hubs.
QU56016 Cap O-Ring for 1993.5-1997 factory manual hubs and Warn® Current Production Spline Mount Replacement Hubs.
QU56012 Original Equipment Warn® Hub Screw for Warn® Spline Mount Hubs in Ford Dana 50IFS Front Axles.
QU40113 Torx® Upgrade Screw for Warn® Spline Mount Hubs in Ford Dana 50IFS Front Axles.
Check Out Now
Manuals and Technical Information
  No Service Publications available at this time.  
     
     
Check Out Now
Miscellaneous Parts
Proper lubrication and replacing damaged or worn small parts is often the difference between a first class, long-term repair and a short lived nightmare. In this section are the small parts and accessory items that do not neatly fit under our other parts headings. Link to Our Ford Web Page Index
S24200 Blue Threadlocker for spindle and ring gear bolts etc.
QU90008 Gear Marking Compound

use with QT9404 Brush to check your ring and pinion gear tooth pattern

 
Anti-Seize Lubricant use between the spindle and knuckle mating surfaces to prevent rust bonding.
PP14 Pyroplex® Protection ES Synthetic Grease provides extended service protection for king pin, axle universal joint, and wheel bearing applications under the harshest on and off road conditions!
SynPower® is a superior quality, moly-fortified, Synthetic Bearing/Chassis Grease for all U.S., European, and Japanese Vehicles.  Use on disc and drum brake wheel bearings, chassis, suspension, universal joints, and CV joints.
Syncon High Performance Synthetic Arctic Grease is an extreme pressure, premium quality, synthetic cold weather grease that provides exceptional protection for bearings and chassis components in sub-zero weather.
707L Red Grease is a premium, extreme pressure, high performance wheel bearing grease with special additives providing excellent rust protection and high resistance to water washout. 707L is an high quality, non-synthetic grease suitable for all 4x4 and light truck disc and drum brake wheel bearing applications, plus it is an ideal grease for chassis lubrication. Available in 14 oz. cartridge or 1 pound tub.
Check Out Now
Pinion Seals and Pinion Yokes
1983-1997 Ford Dana 50IFS Front Axles use a Pinion Yoke made for the oversize 1.125" u-joint cups used on the Ford specific 1330F universal joints (See TK40723 and QU40776). Link to Our Ford Web Page Index
QU20180 Ford Dana 50IFS Front Axle Pinion Yoke is a genuine original equipment Ford Front Pinion Yoke for 1983-1997 Ford F-250 4x4s. This Pinion Yoke fits all Dana 50 IFS (IFS=Independent Front Suspension) Twin Traction Beam™ front drive axles.

     
QU40841 Driveshaft U-Bolt Kit for Ford Dana 50 Front Axle fits all 1983-1997 Ford original equipment Front Dana 50IFS pinion yokes
Check Out Now
Ring and Pinion Kits
  Section under construction  
     
     
Check Out Now
Small Parts
Sometimes, you just need one or two small parts to get back on the road. Between the small parts listed in this section and many others listed under part specific headings elsewhere on the page, we probably have that pesky little part you have to have but just can't find anywhere else. Link to Our Ford Web Page Index

QU40009 Dana 50 Pinion Lock Nut for securing your pinion yoke to the pinion shaft on 1983.5-1997 Ford F-250 and 1980-1985 Ford F-350 4x4 trucks with Dana 50IFS Front Axles.

QU40010 Dana 50 Pinion Washer fits between the pinion nut and pinion yoke on 1983.5-1997 Ford F-250 and 1980-1985 Ford F-350 4x4 trucks with Dana 50IFS Front Axles.
QU40002 Dana 50 Outer Pinion Bearing Slinger goes between your outer pinion bearing and pinion yoke on 1983.5-1997 Ford F-250 and 1980-1985 Ford F-350 4x4 trucks with Dana 50IFS Front Axles.
  QU40527 Dana 50 Inner Pinion Oil Baffle is located under your inner pinion bearing cup on 1983.5-1997 Ford F-250 and 1980-1985 Ford F-350 4x4 trucks with Dana 50IFS Front Axles.
  QU40441 Dana 50 Ring Gear Bolt for 1983.5-1997 Ford F-250 and 1980-1985 Ford F-350 4x4 trucks with Dana 50IFS Front Axles.

QU40343 Dana 50 Differential Cap Bolt is a genuine Dana Grad 8 Bolt. Two of these Bolts are used on each differential bearing cap on 1983.5-1997 Ford F-250 and 1980-1985 Ford F-350 4x4 trucks with Dana 50IFS Front Axles.
  QU40226 Retaining Ring for Ford Dana 50 IFS Differential Output Shafts is a genuine original equipment spring steel Snap Ring that fits in a groove on your innermost right axle shaft on 1983.5-1997 F-250 and 1983.5-1985.5 F-350 Ford 4x4s.
  QU40534 Right Side Differential Output Bearing and Seal Kit for Ford Dana 50 IFS Front Axles is a genuine original equipment Kit that includes the right Axle Shaft Support Bearing, Right Axle Shaft Oil Seal and Axle Shaft Retaining Clip. Fits 1983.5-1997 F-250 and 1983.5-1985.5 F-350 Ford 4x4s.
Check Out Now
Spindles and Spindle Nuts
According to Dana-Spicer, they used only the 4 slot front spindle nut type for 1983-1997 F-350 Dana 60 Front Axles with manual hubs. However, the Ford factory parts lists shows the 6 Slot nut type as being used all the way to early 1985. The only way to know for sure what spindle nut your '83-'85 axle has is to remove the hub-lock and see what is in there!. 1994-1997 Trucks with automatic hubs use a special rounded hex spindle nut. Link to Our Ford Web Page Index
QU40036 6 Slot Spindle Nut is a genuine original equipment replacement nut for either the inner or outer front spindle nut for early Ford Dana 50 IFS front axles. Order 2 Nuts per side.

QU40037 Bend-Over Tab Lockwasher for 6 Slot Spindle Nuts is a genuine original equipment replacement lockwasher that fits between the inner and outer front spindle nut on early Ford Dana 50 IFS front axles.
QU40038 Inner Thrust Washer for 6 Slot Spindle Nuts is a genuine original equipment replacement Thrust Washer that goes between inner front spindle nut and outer wheel bearing on early Ford Dana 50 IFS front axles.
QK4728 6 Slot Spindle Nut Kit for early Ford Dana 50IFS axles includes QU40038 Inner Thrust Washer, Two QU40036 6 Slot Spindle Nuts, and QU40037 Bend Over Tab Spindle Lock Washer.
QU40163 4 Slot Ford Dana50IFS Round Outer Spindle Nut for 1983.5-1997 F-250 and 1983.5-1985.5 F-350 4x4s with manual hubs has 4 slots for QT1018 Spindle Nut Wrench.
QU40164 Ford Dana 50IFS Spindle Lock Washer for 1983.5-1997 F-250 and 1983.5-1985.5 F-350 4x4s with 4 Slot round spindle nuts is reusable.
QU40166 4 Slot Ford Dana 50IFS Round Inner Spindle Nut with Pin for 1983.5-1997 F-250 and 1983.5-1985.5 F-350 4x4s has 4 slots for QT1018 Spindle Nut Wrench. Includes round pin that engages one of the holes in QU40164 Spindle Lock Washer

QK4729 4 Slot Ford Dana 50IFS Round Spindle Nut Kit for 1983.5-1997 F-250 and 1983.5-1985.5 F-350 4x4s includes one each QU40163, QU40164, and QU40166.
  QU20227 Spindle  
     
Check Out Now
Spindle Bearings and Seals 1983-1992
The dead, hollow spindle design of the 1983-1992 era Ford Dana 50 IFS axles use QU40149 needle bearing to support the outer axle shaft. Axial thrust is handled by a plastic thrust washer. Two V-Seals are used to protect the spindle bearing. We stock all the individual components, plus Kits combining the pieces.
For 1993-1997 Model Years, See our Outer Axle Shaft Seal Section for Outer Axle Shaft Bearings, Thrust Washers, and Axle/Spindle Grease Seals
Link to Vehicle Make or Category Links
Click to Enlarge

QU40064 1983-1992 Ford Dana 50 Outer Axle Shaft Slinger is a genuine Dana Spicer part that press fits on the outer axle shafts of Model 60 open knuckle front drive axles for your 1983-1992 Ford Dana 50IFS Front Axle.

Please refer to QU40064 page for more details and ordering information.
Click to Enlarge

QU40065 Large Spindle V-Seal is a genuine Dana Spicer part that fits between the spindle and QU40064 outer axle shaft slinger in Model 60 open knuckle front drive axles on your 1983-1992 Ford Dana 50IFS Front Axle.

Please refer to QU40065 page for more details and ordering information.
Click to Enlarge

QU40066 1983-1992 Ford Dana 50 Outer Axle Shaft to Spindle Thrust Washer is a genuine Dana Spicer part that fits on your Dana 60 outer axle shaft to control thrust between the axle shaft and spindle.

Please refer to QU40066 page for more details and ordering information.
Click to enlarge

QU40148 1983-1992 Ford Dana 50 Small Spindle V-Seal is a genuine Dana Spicer part that fits in the back of your spindle between QU40149 spindle bearing and QU40066 thrust washer in 1983-1992 Ford Dana 50IFS Front Axles.

Please refer to QU40148 page for more details and ordering information.
QU40149 1983-1992 Ford Dana 50 Spindle Bearing is a genuine Dana Spicer original equipment part that is a press fit in the back of the spindle. This bearing is the primary support for your outer axle shaft.
Click to enlarge QK4740 1983-1992 Ford Dana 50 6 Piece Large Spindle Seal and Thrust Washer Kit services BOTH sides of your 4x4 with two each of these parts: QU40065 Large Spindle V-seal, QU40066 Spindle Thrust Washer, and QU40148 Small Spindle V-seal.
Click to enlarge QU40168 1983-1992 Ford Dana 50 Spindle Bearing and Seal Kit services ONE side of your 4x4 with one each of these parts: QU40065 Large Spindle V-seal, QU40066 Spindle Thrust Washer, QU40148 Small Spindle V-seal, and QU40149 Spindle Bearing.
Check Out Now
Steering Knuckles
     
  This section under construction  
     
     
Check Out Now
Steering Linkage Parts
     
  This section under construction  
     
     
Check Out Now
Tools
     
QT5500 Wheel Bearing Packer takes the mess out of packing wheel bearings, plus it minimizes the chances of getting contaminants mixed with your wheel bearing grease. The QT5500 Bearing Packer does an absolutely beautiful job of forcing grease between the individual bearing rollers. The easiest and most efficient way to repack the front wheel bearings on your big Ford!
QT1815 Dana 50 Inner Pinion Bearing Cup Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50539 Inner Pinion Bearing Cup a simple and fast procedure.
QT1812 Outer Pinion Bearing Cup Installer Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50533 Outer Pinion Bearing Cup a simple and fast procedure.
     
     
QT1025 6 Prong Spindle Nut Socket for 6 Slot Round Nuts used on early Ford Dana 50IFS Front axles with QU40036 Spindle Nuts.
QT1110 4 Prong Spindle Nut Socket for 4 Slot Round Nuts used on later Dana 50IFS Front axles with QU40163 and QU40166 Spindle Nuts.
QT1100 Series Driver Handles are used in conjunction with our seal and bearing cup installers.

QT1033 Case Spreader is used to relieve the differential bearing preload making it easy to safely remove and install your front differential without damaging expensive critical parts. (Dana 50 axles also require you fabricate adapters with 2 pins)

Please refer to QT1033 page for more details and ordering information.

QT1023 Triple Thread Universal Spindle Puller Use with any 5/8" fine thread slide hammer to quickly and easily remove those rusted in QU40169 or QU40420 front wheel bearing spindles on your 1983-1997 Ford Dana 50 front drive axle without damage! Essential for servicing axle u-joints, king pins, spindle bearings, inner axle seals, and differentials. Also works on most GM 10 Bolt, Dana 50IFS, Dana 44, Dana 30, Dana 27, and Dana 25 front axles.


QT1024 Triple Thread Ford Spindle Puller Use with any 5/8" fine thread slide hammer to quickly and easily remove those rusted in QU40169 or QU40420 front wheel bearing spindles on your 1983-1997 Ford Dana 50 front drive axle without damage! Essential for servicing axle u-joints, king pins, spindle bearings, inner axle seals, and differentials. Also works on most Dana 44, Dana 35 IFS, and Ford Dana 28IFS front axles.

QT1200 Tie Rod Separator allows you to remove the separate tie rod and drag link ends without wrecking the seals or screwing up your steering linkage ends.

QT9018 5 Pound Dead Blow Hammer is just about the first tool you will reach for to complete a multitude of jobs on your Dodge Ram. From seating differentials to removing rusted on wheels, the ability to apply persuasive force without damaging the reluctant part will make you wonder how you ever lived without this essential tool.

Please refer to QT9018 page for more details and ordering information.

QT9302 5 Pound Slide Hammer a first-class tool for pulling just about anything you can get a matching 5/8" fine thread puller attachment for.

Please refer to QT9302 page for more details and ordering information.

Click to enlarge		 QT1801 Outer Wheel Bearing Cup Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50411 Outer Wheel Bearing Cup a simple and fast procedure.

Click to enlarge		 QT1804 Inner Wheel Bearing Cup Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50396 Inner Wheel Bearing Cup a simple and fast procedure.
Click to Enlarge QT1505 Front Wheel Seal Installer is custom made to quickly and easily install your new wheel seals without damaging them.
Check Out Now
Wheel Bearings and Seals (Individual)
Ford used only the best wheel bearings and seals money could buy to equip their Dana 50 IFS front axles to minimize the chance for warranty problems. That is why they chose Timken® Wheel Bearings and Spicer Wheel Seals for heavy-duty Ford F-250 and F-350 4x4s using the IFS Dana 50. We supply those exact original equipment replacement Timken® Wheel Bearings and Spicer Wheel Seals to keep your Ford on the job for years to come. Link to Vehicle Make or Category Links
QU50411 Timken® Outer Wheel Bearing Cup for all 1983.5-1997 F-250 and 1983.5-1985.5 F-350 4x4 Dana 50 IFS front drive axles.
QU50412 Timken® Outer Wheel Bearing for all 1983.5-1997 F-250 and 1983.5-1985.5 F-350 4x4 Dana 50 IFS front drive axles.
QU50396 Timken® Inner Wheel Bearing Cup for all 1983.5-1997 F-250 and 1983.5-1985.5 F-350 4x4 Dana 50 IFS front drive axles.
QU50398 Timken® Inner Wheel Bearing for all 1983.5-1997 F-250 and 1983.5-1985.5 F-350 4x4 Dana 50 IFS front drive axles.
QU40119 Inner Wheel Seal is a genuine Dana-Spicer original equipment replacement part for all 1983.5-1997 F-250 and 1983.5-1985.5 F-350 4x4 Dana 50 IFS front drive axles.
     
Check Out Now
Wheel Bearing and Seal Kits
Ford used the same wheel bearing and seal numbers for the entire 1983 to 1997 production run of Dana 50IFS front drive axles. However, spindle nut sets will vary by year. We offer Wheel Bearing Part/Tool Kits with or without bearing and seal installation tools. If you need a spindle nut socket, see QT1025 for 1983-1985.5 trucks or QT1110 for 1985.5-1997 models with manual hubs or QT1058 Rounded Hex Spindle Nut Socket for 1994-1997 trucks with factory auto locking hubs.  
TK4744 Torque King® 1992-1997 Front Wheel Bearing and Seal Kit without Tools is a parts only (No Tools) complete front Wheel Bearing and Seal Kit for your heavy-duty Ford featuring Timken® Bearings and original equipment wheel seals for all 1992-1997 Ford F-350 4x4 Dana 60 front drive axles. Kit includes 2 each of Timken® Inner and Outer Wheel Bearings/Bearing Cups, plus two Wheel Seals.
TK4738 Torque King® 1992-1997 Front Wheel Bearing and Seal Kit with Install Tools for all 1992-1997 Ford F-350 4x4 Dana 60 front drive axles. Kit includes Inner Wheel Bearing Cup Installer, Outer Wheel Bearing Cup Installer, Wheel Seal Installer, Driver Handle, plus 2 each of Timken® Inner and Outer Wheel Bearings/Bearing Cups, plus two Wheel Seals. This Kit DOES NOT INCLUDE Spindle Nut Socket or Hub Small Parts for your Ford!!!
Check Out Now