Parts for Dana-Spicer Model 60 Front Axles in 1975 IHC 4x4 Trucks

We stock a complete line of parts for the open knuckle, Dana-Spicer Model 60 Front Axle which was first used by IHC in the 1975 1 ton 1300 Camper Special 4x4 truck. The newly released Model 60 axle used the same size axle universal joint as the previous Model 70 closed knuckle axle, but the new open knuckle design had a sharper turning angle which substantially improved vehicle maneuverability.

The Model 60 has very durable greaseable king pins and disc brakes. The wheel bearings are serviceable and the dead-spindle configuration allows the use of lockout hubs.

Axle Identification
Dana Axle ID Tag
Click to enlarge 		All 1975 Dana 60 Front Axles in International trucks had a Bill of Material Number (BOM) stamped on the front side of the right axle tube. The BOM number is a 6 digit number beginning with a 6 plus a dash number (ex: 610604-2). They can be used to determine not only the axle model, but also what components the axle was originally built with. We often ask for this number to insure we provide you with the exact parts you need for your truck.

Each different BOM number signifies an engineering part change which may be minor or major and may involve one or more parts. The dash number indicates the axle ratio and, for some years, the front wheel hub style (for single or dual rear wheel models).


Link to Vehicle Make or Category Links
Dana 60 Diff CoverClick to Enlarge

Both Model 60 and 61 axles share almost all the same parts except for the axle housing and gear sets. The Model 60 was designed in an era of small engines requiring low gears to move the vehicle so the lowest numeric ratio it was designed for was 3.54:1. By the mid 1980's, fuel economy became paramount so lower numeric gears were needed to reduce the engine rpm, especially with non-overdrive transmissions and/or slow turning diesel engines. The Model 61 has the pinion center line set farther from the ring gear so a larger diameter pinion head can be accommodated. For International front axles, the Model 61 was only available with 3.07 and 3.54 ratio gear sets. Depending on the year and engine, the Model 60 could be ordered with 3.54, 4.10, 4.56, 4.88, or 5.86 gearing.

Cover: 10 Bolt, 12" high

Ring Gear: 9-7/8", 12 Bolt

  
  Suspension: Leaf spring  
  Steering Linkage: 1975-1993 uses a tie rod that attaches to each steering knuckle. Drag link goes from steering gear to cast iron arm bolted to the top of the drivers side steering knuckle.  
  Knuckle Mounting: Greaseable King Pins. Upper uses spring loaded plastic bushing rotating on a tapered King Pin. Lower has tapered roller bearing.  


Click to Enlarge


Click to Enlarge

Wheel Hub: Two types of wheel hubs were used for Dana 60 and Dana 61 front axles. Early and mid production trucks used a wheel hub that took 8 bolt, externally mounted drive flanges or lockout hubs. Late production trucks used an internally splined wheel hub. Each hub type had a version for single rear wheel trucks and dual rear wheel trucks. There is conflicting documentation on the exact dates of the change over from external type hub mounting to internal, most likely due to the fact trucks were being manufactured in Canada, Mexico, and the United States at the same time and each plant probably made the switch when their inventory of axles with external type hubs was used up. According to International parts books, all 1989 and prior models have the external mount hub. Dana however, lists both external and internal hubs for 1989. Our own experience has been that 1989 models all have external type hubs, but we believe there may be some late production 89's with the internal hub. For 1990 to 1991, IHC lists both external and internal hubs. Dana lists only internal. We have seen a few 1990 models with external hubs, but most are internal. For 1991, most if not all, trucks should have internal hubs, but we did work on at least one 1991 dually with external hubs, so presumably there are more out there. 1992 and 1993 is easy, IHC, Dana, and our experience, all agree these years will have internal hubs.

The 1975-1991 external, 8 bolt type wheel hub was factory equipped with either a splined steel drive flange or Selectro® lock out hubs with big cast aluminum selecter knobs. 1990-1993 Internal spline wheel hubs had factory installed Warn® plastic dial lockout hubs.

  
1979-1980 Bill of Material Numbers Model 60: 603643
Model 61: No Model 61 for these years		  
1981-1988 Bill of Material Numbers

Model 60: 610135, 610236
Model 61: 610265 (1987-1988 only)

  
1989-1990 Bill of Material Numbers Model 60: 610332, 610341
Model 61: 610333, 610342 (both listed for 1989 only)		  
1991 Bill of Material Numbers Model 60: 610357
Model 61: 610358		  
1992 Bill of Material Numbers Model 60: 610398, 610430
Model 61: 610358, 610431		  
1993 Bill of Material Numbers Model 60: 610405
Model 61: 610406		  
Check Out Now
Axle Assemblies and Axle Housings
     
     
     
     
     
     
     
     
     
Axle Shafts
     
     
     
     
     
     
     
     
     
Axle Shaft Seals and Seal Kits
An Inner Axle Seal is pressed in the inboard end of each axle tube, right next to the differential side bearings. These seals contact the inner axle shafts to prevent gear oil from running out of the differential and down the axle tubes. Old age, blown axle u-joints, and/or grit that works it's way into the axle tubes and cuts the seal are the usual causes of failure. A bad Inner Axle Shaft Seal can be detected by oil coming out the end of the axle tubes next to the axle shaft u-joint. Usually when these Seals start to fail, they will seep oil so the leakage may go undetected for quite some time. Many a ring and pinion set has been burned up from axles that lost all their lube when long term seepage was not noticed.


Link to Vehicle Make or Category Links

Click to Enlarge

QK4656 Adjustable Depth Type Inner Axle Shaft Seal Tool and Seal Kit for 1975 International 4x4s with Model 60 front axles.  Includes 2 QU40059 Axle Seals, QT1042 Adjustable Depth Seal Installer, QT1133 Alloy Steel Press Screw with Hardware, & QT1130 Thrust Plate. 

Please refer to QK4656 page for more details and ordering information.

Click to Enlarge

TS4656 Adjustable Depth Type Inner Axle Shaft Seal Tool Set for 1975 International 4x4s with the Model 60 front axles.  Includes QT1042 Adjustable Depth Seal Installer, QT1133 Alloy Steel Press Screw with Hardware, & QT1130 Thrust Plate. Purchase QU40059 Axle Seals separately.

Please refer to TS4656 page for more details and ordering information.

QK4867 Fixed Depth Type Inner Axle Shaft Seal Tool and Seal Kit for 1975 International 4x4s with the Model 60 front axles.  Includes 2 QU40059 Axle Seals, QT1156 Fixed Depth Seal Installer, QT1133 Alloy Steel Press Screw with Hardware, & QT1130 Thrust Plate.

TS4867 Fixed Depth Type Inner Axle Shaft Seal Tool Set for 1975 International 4x4s with the Model 60 front axles. Includes QT1156 Fixed Depth Seal Installer, QT1133 Alloy Steel Press Screw with Hardware, & QT1130 Thrust Plate. Purchase QU40059 Axle Seals separately.
Click to Enlarge QU40059 Inner Axle Shaft Seal One of these Seals are installed in each axle tube, right next to the differential to keep gear lube from leaking out the ends of the axle housing on all 1975 International 4x4s with the Model 60 front axles.
See our Spindle Seal and Bearing Section for Outer Axle Shaft Slingers, Thrust Washers, and Axle/Spindle Grease Seals  
     
     
     
     
     
     
     
     
     
Axle Universal Joints
We offer three different Universal Joints for your hard working International 4x4. All are plenty strong for the job, but different manufacturing techniques and seal types will have a major influence on the ultimate life of the joint. Our most popular choice is our TK40715 cold-forged, non-greaseable, original equipment replacement U-Joint. The wear-resistant cold-forged cross and superior sealing make it the best choice for both low maintenance and long life. Greaseable TK40724 U-Joints are a greaseable version of our TK40715 joints, giving you the durability advantages of cold-forging and better seals with the option to re-lube the joint at any time for unmatched longevity. QU30332's are hot-forged and equipped with simple rubber seals. With good maintenance and quality lubricant like our Pyroplex® Plus Grease, these joints will last and last. See our individual product pages for more info.


Link to Vehicle Make or Category Links
QU30332 Greaseable Axle U-Joint

for 1975 International 4x4s with the Model 60 front axles.

Please refer to QU30332 page for more details and ordering information.
TK40715 Torque King® Premium Non-Greasable U-Joint

for 1975 International 4x4s with Model 60 front axles.

Please refer to TK40715 page for more details and ordering information.
TK40724 Torque King® Greasable U-Joint

for 1975 International 4x4s with Model 60 front axles.

Please refer to TK40724 page for more details and ordering information.
     
     
     
     
     
     
     
     
     
Brake Parts
     
     
     
     
     
     
     
     
     
Differential and Pinion Bearings (Individual)
Over the years, Dana has primarily used Timken bearings when building their axles. For long life and dimensional consistency, Timken bearings are unmatched by any other brand of bearing I have used rebuilding axles over the past 30+ years in the business. When you are a shade tree mechanic dealing with a diff and pinion rebearing job without all the fancy gauging tools we have, you always want your new bearings to be the same overall thickness as the original bearings were when the axle was built so your pinion depth, pinion preload and backlash are within the tolerance limits when you are done with the job. Timken bearings will almost always deliver that type of accuracy, plus the steel quality and surface finish is the world's best.


Link to Vehicle Make or Category Links

QU50397 Differential Bearing Cup for 1975 International 4x4s with Model 60 front axles. Fits both single rear wheel and dual rear wheel trucks.

Please refer to QU50397 page for more details and ordering information.


QU50398 Differential Bearing for 1975 International 4x4s with Model 60 front axles. Fits both single rear wheel and dual rear wheel trucks.

Please refer to QU50398 page for more details and ordering information.

QU50400 Outer Pinion Bearing Cup for Dana Model 60 1975 International 4x4s front axles. Fits both single rear wheel and dual rear wheel trucks.

Please refer to QU50400 page for more details and ordering information.


QU50401 Outer Pinion Bearing for 1975 International 4x4s with Model 60 front axles. Fits both single rear wheel and dual rear wheel trucks.

Please refer to QU50401 page for more details and ordering information.


QU50406 Inner Pinion Bearing Cup for 1975 International 4x4s with Model 60 front axles. Fits both single rear wheel and dual rear wheel trucks.

Please refer to QU50406 page for more details and ordering information.


QU50407 Inner Pinion Bearing for 1975 International 4x4s with Model 60 front axles. Fits both single rear wheel and dual rear wheel trucks.

Please refer to QU50407 page for more details and ordering information.

     
     
     
     
     
     
     
     
     
Differential Bearing and Seal Kits
Torque King® Premuim Diff Bearing and Seal Kits are the #1 choice for those who depend upon their truck to keep working day in and day out no matter how tough the conditions. Our Kits combine the supurb quality of Timken bearings with the precise fit and relability of 100% genuine Dana-Spicer small parts. No aftermarket, off brand or Chinese knockoff parts in these Kits!

Link to Vehicle Make or Category Links
TK4864 Torque King® Premium Quality Front Differential Bearing and Seal Kit for your 1975 International heavy-duty 4x4 truck features 100% Timken® Bearings and genuine Dana-Spicer Small Parts. TK4864 includes: QU50400 Outer Pinion Bearing Cup, QU50401 Outer Pinion Bearing, QU50406 Inner Pinion Bearing Cup, QU50407 Inner Pinion Bearing, 2 QU50397 Differential Bearing Cups, 2 QU50398 Differential Bearings,QU40097 Pinion Seal, QU40099 Outer Pinion Slinger, QU40022 Pinion Nut, QU40023 Pinion Washer. Almost all parts USA Made, but some are imported.

Dan the Gear Man® Product Note: TK4864 Kit does NOT include QU40059 Axle Shaft Seals. Order those separately or as part of QK4656 Axle Shaft Seal Kit.

Please refer to TK4864 page for more details and ordering information.
TK4865 Torque King® Premium Quality Front Differential Master Service Kit for your 1975 International heavy-duty 4x4 truck features 100% Timken® Bearings and genuine Dana-Spicer Small Parts. TK4865 includes: QU50400 Outer Pinion Bearing Cup, QU50401 Outer Pinion Bearing, QU50406 Inner Pinion Bearing Cup, QU50407 Inner Pinion Bearing, 2 QU50397 Differential Bearing Cups, 2 QU50398 Differential Bearings,Pinion Preload Shims, QU40365 Pinion Depth Shims, QU40206 Differential Shims, 12 QU40086 Ring Gear Bolts, QU40097 Pinion Seal, QU40099 Outer Pinion Slinger, QU40022 Pinion Nut, QU40023 Pinion Washer, QU40519 Lock Pin, 2 QU40059 Axle Shaft Seals, QU90008 Gear Marking Compound, S82194 Ultra RTV Sealant, S24200 Threadlocker, and QT9404 Brush. Almost all parts USA Made, but some are imported.

Dan the Gear Man® Product Note: This Kit does not include QU40041 Side Gear Thrust Washers, or QU40518 Pinion Mate Gear Thrust Washers.

Please refer to TK4865 page for more details and ordering information.
     
     
     
     
     
     
     
     
     
Differential Parts
Differential problems with Model 60 and 61 front axles are not all that common. But Murphy, of Murphy's Law* really likes busted differentials, so when you hear that loud, heart-stopping, ominous BANG from the front axle as your 4x4 lurches to a grinding stop, you just KNOW it is one big dose of bad news. To help get you back on the road after you get rescued, we stock genuine original equipment Dana-Spicer Front Axle Differential Parts for your hard working 1975 International 4x4 truck.
*Murphy's Law: "Anything that can go wrong, will go wrong"
Link to Vehicle Make or Category Links
QU40254 Bare Differential Case Kit is a genuine Dana-Spicer Model 60 and Model 61 Case for 3.07, 32.54, and 4.10 ratio ring and pinion sets. Kit includes Differential Case, 12 QU40086 Ring Gear Bolts and QU40206 Differential Shim Kit.

Please refer to QU40254 page for more details and ordering information.

QU40331 Dana 60 or 61 Differential Inner Parts Kit includes 2 differential side gears, 2 QU40518 pinion mate thrust washers, 2 differential pinion mate gears, 2 QU40041 side gear thrust washers, QU40520 differential cross shaft, QU40519 cross shaft retaining pin, 12 QU40086 ring gear bolts, and differential adjusting shims.
QU40518 Differential Pinion Mate Thrust Washer Two of these Thrust Washers are used in each differential, one between each pinion mate gear and the differential case.

Please refer to QU40518 page for more details and ordering information.

QU40041 Differential Side Gear Thrust Washer Two of these Thrust Washers are used in each differential, one between each side gear and the differential case.

Please refer to QU40041 page for more details and ordering information.
QU40520 Differential Cross Shaft.

Please refer to QU40520 page for more details and ordering information.
QU40519 Lock Pin for Differential Cross Shaft is used to lock QU40520 differential cross shaft to the diff case.

Please refer to QU40519 page for more details and ordering information.

Ring and Pinion Kits: See Our Ring and Pinion Section Below

  
     
     
     
     
     
     
     
     
     
Gaskets and Gasket Makers
QU40367 Rear Differential Cover Gasket for Model 70 Axles. These genuine Dana-Spicer gaskets will also work on your Dana 60 front axles if you wish to use a Gasket in lieu of RTV sealant. Made in U.S.A.

Please refer to QU40367 page for more details and ordering information.

Dan the Gear Man® Tech Note: RTV sealant instead of Gaskets were used during the factory assembly of your axle.
S82194 Ultra Gray RTV Sealant combines high adhesion and resistance to both conventional and synthetic gear lubes. The perfect choice to seal the differential cover on your Dodge Ram.

Please order your S82194 Ultra Gray RTV Sealant from our Shop Supplies Web Page.
     
     
     
     
     
     
     
     
     
Hubs and Hub Parts
     
     
     
     
     
     
     
     
     
King Pin Kits and Parts
We stock all the normal replacement parts for Dana 60 King Pin type Front Axles. 1975 International Dana 60 and Dana 61 front axles use greaseable and rebuildable King Pins instead of Ball Joints to mount the steering knuckles to the axle housing. Time has proven the Dana 60/Dana 61 King Pin design to be the most durable front axle steering components ever installed in Class 2 3/4 ton and Class 3 1 ton 4x4 trucks. Although at first glance the number of King Pin parts may appear daunting, the fact is King Pins front axle components are usually pretty easy to replace if they ever need service beyond regular greasing. Link to our Dodge Web Page Index
QK4512 Dana Model 60 King Pin Kit for 1975 International 4x4 trucks with Model 60 King Pin type front axles. Kit includes spindle seals, spindle thrust washers, lower king bearing assemblies, king pin seals, lower king pin grease retainers, upper king pin bushings, tension springs, spring plates, anti-seize, Threadlocker, disc brake lube, RTV sealant, & cotter keys for the tie rod ends.
QU40191 Dana 60 Lower King Pin Bearing and Seal Kit for 1975 International 1300 4x4s equipped with Dana Spicer Model 60 front drive axles includes one each these genuine

Dana replacement parts: QU40062 Lower Grease Reatainer, QU50600 Lower King Pin Bearing, QU50601 Lower King Pin Bearing Cup, QU40092 Lower King Pin Seal, QU40147 Upper King Pin Seal. Order two Kits per vehicle. Also See QK4512 King Pin Kit
QK4550 Dana 60 and Dana 61 Upper King Pin and Wrench Set includes 3/4" Drive Impact Socket/Hex Bit Socket, 2 genuine Dana Spicer Upper King Pins, and S9979 High Strength Threadlocker.
QU40266 Dana 60 Upper King Pin is a genuine Dana Spicer service part for your 1975 International 1300 Dana 60 open knuckle, king pin front end.
QU40157 Dana 60 Upper King Pin Spring Retainer Plate is a genuine Dana Spicer replacement part for

1975 International 4x4s equipped with Dana Spicer Model 60 front drive axles. This Retainer Plate fits between QU40265 Tension Spring and QU40093 Upper King Pin Bushing. The raised inner rim keeps the Spring centered over the bushing. Made in U.S.A. Also see QK4512 King Pin Kit.
QU40265 Dana 60 Upper King Pin Spring This genuine original equipment Dana Spicer heavy-duty coil spring applies constant tension to QU40093 Upper King Pin Bushing to automatically adjust for wear and dampen road shock. QU40265 fits 1975 to 1993 model years on all Chevy, Dodge, Ford, GMC, and IHC

3/4 ton and 1 ton 4x4 trucks equipped with either the Dana Spicer Model 60 or Model 61, open knuckle front axles with King Pins.
QU40093 Dana 60 Plastic Upper King Pin Bushing This long lasting, genuine original equipment Dana Spicer split plastic bushing has a tapered ID to match QU40266 Upper King Pin. QU40093 fits 1975 to 1993 model years on all Chevy, Dodge, Ford, GMC, and IHC

3/4 ton and 1 ton 4x4 trucks equipped with either the Dana Spicer Model 60 or Model 61, open knuckle front axles with King Pins. Also see QK4512 King Pin Kit.
QU40147 Dana 60 Upper King Pin Seal is a genuine Dana Spicer service part for all 1975 International Model 60 and Model 61 open knuckle front drive axles.

Also see QK4512 and QU40191 King Pin Kits.
QU40063 Dana 60 Upper King Pin Gasket is a genuine Dana Spicer replacement Gasket for all 1975 King Pin type Model 60 and Model 61 open knuckle front drive axles.

A high quality cut gasket that seals between your steering knuckle and upper king pin cap/steering arm. Use two QU40063 Gaskets per vehicle. Made in Indonesia. Also see QK4512 King Pin Kit.

QU40062 Dana 60 Lower King Pin Grease Retainer is a genuine Dana Spicer service part for all 1975 IHC 1300 King Pin type Model 60 and Model 61 open knuckle front drive axles.
QU50600 Large King Pin Bearing for Dana Heavy Duty Front Axles for all 1975 International Model 60 and Model 61 open knuckle front drive axles.

Also see QK4512 and QU40191 King Pin Kits.
QU50601 King Pin Bearing Cup fpr Dana 60 and Dana 70 Front Axles for all 1975 International Model 60 and Model 61 open knuckle front drive axles.

Also see QK4512 and QU40191 King Pin Kits.
QU40092 Dana 60 Lower King Pin Seal is a genuine Dana Spicer service part for all 1975 IHC 1300Model 60 and Model 61 open knuckle front drive axles.

Also see QK4512 and QU40191 King Pin Kits.
QU30064 Dana 60 Upper King Pin Cap/Steering Arm Stud is a genuine original equipment replacement part for securing the drivers side steering arm to the steering knuckle on all 1975 International 1300 Model 60 and Model 61 open knuckle front drive axles.
     
Check Out Now
Manuals and Technical Information
TM4400P Pinion and Differential Bearing Service On Dana-Spicer Monobeam Axles.
VSG4506 Model 60 King Pin Service Video (Previously named QK4512DVD or V4512DVD) shows you how to perform King Pin Service on your 1975 International 4x4 Model 60 or Model 61 open knuckle 4x4 front drive axle.
Check Out Now
Miscellaneous Parts
S24200 Blue Threadlocker

Please order your S24200 Blue Threadlocker from our Shop Supplies Web Page.
QU90008 Gear Marking Compound

Please order your Gear Marking Compound from our Shop Supplies Web Page.
PP14 Pyroplex® Protection ES Synthetic Grease provides extended service protection for king pin, axle universal joint, and wheel bearing applicaions under the harshest on and off road conditions!
SynPower® is a superior quality, moly-fortified, Synthetic Bearing/Chassis Grease for all U.S., European, and Japanese Vehicles.  Use on disc and drum brake wheel bearings, chassis, suspension, universal joints, and CV joints.
Syncon High Performance Synthetic Arctic Grease is an extreme pressure, premium quality, synthetic cold weather grease that provides exceptional protection for bearings and chassis components in sub-zero weather.
707L Red Grease is a premium, extreme pressure, high performance wheel bearing grease with special additives providing excellent rust protection and high resistance to water washout. 707L is a high quality, non-synthetic grease suitable for all 4x4 and light truck disc and drum brake wheel bearing applications, plus it is an ideal grease for chassis lubrication. Available in 14 oz. cartridge or 1 pound tub.
Check Out Now
Pinion Seals and Pinion Yokes
     
QU40097 Pinion Seal for Dana 60 and Dana 61 Front Axles. This genuine Dana-Spicer original equipment service part fits all 1975 IHC 1300 4x4s with Model 60 and Model 61 open knuckle front drive axles in IHC 4x4 trucks.
     
     
     
     
     
     
     
     
Ring and Pinion Kits
Unless your axle has run out of oil or it is severely abused, you will probably never have to replace your original ring and pinion set. However, if you do need one, we stock original equipment Dana-Spicer Gear Sets for your vintage IHC 1300 Dana 60 or Dana 61 front axle. These genuine gear sets are not cheap when compared to the host of knock off Asian import gear sets being pushed into the market place by vendors focused on getting the cheapest stuff they can. Well, like anything, you get what you pay for. I have been setting up Dana Gear Sets since the mid 1970's to date, and I have never had a setup problem with a genuine Dana-Spicer Gear Set. The same is not true for the aftermarket parts. Besides having sloppy machining, most aftermarket gears are not made to use the Dana factory set up tools, so a person usually has to apply some blood-boiling "Kentucky Windage" to the setup procedure to make progress!
Link to Vehicle Make or Category Links
QU40481 Dana 60 and Dana 61 3.54 Ratio Gear Set is a genuine Dana Spicer gearset that includes matched 3.54 ratio ring and pinion gears, Inner and Outer Pinion Bearings with Cups. 12 Ring Gear Bolts, pinion seal, Pinion Nut, Pinion Washer, Outer Pinion Slinger, Inner Pinion Slinger, Inner Pinion Baffle, Diff Cover Gasket, Pinion Depth Shims, Pinion Preload Shims, and Differential Adjusting Shims
QU40252 Dana 60 4.10 Ratio Gear Set is a genuine Dana Spicer gearset that includes matched 4.10 ratio ring and pinion gears, Inner and Outer Pinion Bearings with Cups. 12 Ring Gear Bolts, pinion seal, Pinion Nut, Pinion Washer, Outer Pinion Slinger, Inner Pinion Slinger, Inner Pinion Baffle, Diff Cover Gasket, Pinion Depth Shims, Pinion Preload Shims, and Differential Adjusting Shims
Check Out Now
Small Parts
Sometimes, you just need one or two small parts to get back on the road. Between the small parts listed in this section and many others listed under part specific headings elsewhere on the page, we probably have that pesky little part you have to have but just can't find anywhere else. Link to Vehicle Make or Category Links

QU40064 Slinger for Outer Axle Shaft presses on your 1975 IHC 1300 Model 60 or Model 61 outer axle shaft and acts as both the mounting surface and protective slinger for QU40065 Spindle V-Seal.

Please refer to QU40064 page for more details and ordering information.
QU40343 Dana 60 Hardened Differential Cap Retaining Bolt Genuine original equipment hex-head bolt for Dana Spicer Model 60 and 61 front axle differential bearing caps fits all IHC 1300 4x4 trucks the Dana 60 front drive axle.

Please refer to QU40343 page for more details and ordering information.
Click to Enlarge QU40022 Dana 60 Pinion Nut Genuine original equipment pinion nut for Dana Spicer Model 60 and 61 front axle differential bearing caps fits all 1975 IHC 1300 4x4s with Dana 60 front drive axle. QU40022 is a genuine original equipment, self-locking nut, intended for a single use part, discard and replace with a new nut any time you remove the pinion nut.

Also included in TK4864 and TK4865

Please refer to QU40022 page for more details and ordering information.
Click to Enlarge QU40023 Dana 60 Pinion Washer for Dodge Ram is a genuine original equipment flat washer that goes between the pinion nut and pinion yoke. Fits all 1975 IHC 1300 4x4 trucks with either the Dana 60 or Dana 61 front drive axle.

Also included in TK4864 and TK4865

Please refer to QU40023 page for more details and ordering information.
QU40207 Dana 60 and Dana 61 Differential and Pinion Shim Kit for Dana-Spicer Model 60 or 61 front axles in 1975 International 1300 4x4s. Genuine Dana-Spicer Shim Kit includes Pinion depth shims, pinion preload shims, differential adjusting shims, pinion nut, and cover gasket.

QU40206 Dana 60 Differential Bearing Shim Kit includes a selection of genuine original equipment Shims for adjusting backlash and differential bearing preload on your 1975 IHC 1300 4x4s with Dana 60 or Dana 61 front drive axles.

Also included in TK4865 and QU40207

Please refer to QU40206 page for more details and ordering information.
QU40099 Dana 60 Outer Pinion Slinger fits between the outer Pinion Bearing and Pinion Yoke. QU40099 is a genuine original equipment Dana Spicer part. Fits all 1975 IHC 1300 4x4s with Dana 60 front drive axle.


Also included in TK4864 and TK4865

Please refer to QU40099 page for more details and ordering information.
QU40086 Dana 60 Ring Gear Bolt for Dana 60 or Dana 61. Genuine Dana-Spicer Grade 9 Bolt has locking teeth under the hex head to prevent loosening under any load conditions.

Also included in TK4865

Please refer to QU40086 page for more details and ordering information.

Dan the Gear Man® Safety Note: Ring Gear Bolts are designed for a single use. They must be replaced after they are removed!
     
Check Out Now
Spindles and Spindle Nuts
Dodge used the same QU40293 front spindle on all 1975 Model 60 or 61 open knuckle front drive axle. Spindle nuts are a different story. IHC 1300 used a 2-9/16" hex nut with a bend over tab lock washer from 1975 to 1991. For 1992 and 1993, a round 4 slot double nut design was used. It is not uncommon to find the newer nut set used on the older trucks or vice a versa. We used to see this a lot on fleet trucks where the nut styles were apparently changed for standardization reasons.
Link to Vehicle Make or Category Links
Click to enlarge

QU40293D Spindle Kit for all 1975 IHC 1300 4x4 trucks with Dana-Spicer Model 60 and Model 61 Front Axles.

Click to Enlarge QU40051 Bend Over Tab Spindle Lock Washer for 1975 IHC 1300 4x4 is a single use part that should be replaced any time the wheel nuts are adjusted.
Click to Enlarge

QU11070 Hex Spindle Nut for 1975 IHC 1300 4x4. Measures 2-9/16" across the flats.
QU40163 Round Outer Spindle Nut for 1975 IHC 1300 4x4 has 4 slots for QT1018 Spindle Nut Wrench.
QU40164 Spindle Lock Washer for 1975 IHC 1300 4x4 with round spindle nuts is reuseable.
QU40166 Round Inner Spindle Nut with Pin for 1975 IHC 1300 4x4 4x4 has 4 slots for QT1018 Spindle Nut Wrench. Includes round pin that engages one of the holes in QU40164 Spindle Lock Washer.
QK4729 Round Spindle Nut Kit for 1975 IHC 1300 4x4 includes one each QU40163, QU40164, and QU40166.

QK4730 Replacement Spindle Nut Kit for 1975. This Dana provided replacement nut and washer components for your older IHC uses nuts that measure 2.5" across the flats instead of 2-9/16" so you will need QT1013 Spindle Nut Wrench.

Dan the Gear Man Tech Note: Dana has listed the QK4730 components as the correct replacement parts for IHC Dana 60F axles equipped with hex nuts since the late 1970's. These are the parts we have used on customer trucks since that time. So if you need the entire nut set for your 1975-1991 4x4, and wish to save a few $$, order this Set instead of 2 QU11070 nuts and 1 QU40051 Washer, just remember the hex size is slightly smaller!
QU95037 Heat-treated, All Metal, Spindle to the Steering Knuckle Lock Nut Six of these USA Made, 150,000 psi rated Locknuts fit on QU40541 Spindle to Knuckle Bolt to secure each of your QU40293D Spindles to the Steering Knuckles.
Click to Enlarge QU40541 Spindle-to-Knuckle Bolt Six of these press-in special bolts fit each steering knuckle. They are used along with QU95037 Locknut to retain your spindles and caliper anchor plates.
Check Out Now
Spindle Bearings and Seals
The dead spindle design of the 1975 International 1300 4x4 Dana 60 series axles uses QU40149 needle bearing to support QU40330D outer axle shaft. To protect the bearing and control axial thrust, a 4 piece set consisting of QU40064 Slinger, QU40065 Large V-Seal, QU40148 Small V-Seal, and QU40066 Thrust Washer was used. We have both Kits and individual exact replacement Dana-Spicer Spindle small parts for your hard-working IHC.
Link to Vehicle Make or Category Links
Click to Enlarge

QU40064 Outer Axle Shaft Slinger is a genuine Dana Spicer part that press fits on the outer axle shafts of Model 60 or Model 61 open knuckle front drive axles for your 1975 IHC 1300 4x4.

Please refer to QU40064 page for more details and ordering information.
Click to Enlarge

QU40065 Large Spindle V-Seal is a genuine Dana Spicer part that fits between the spindle and QU40064 outer axle shaft slinger in Model 60 or Model 61 open knuckle front drive axles on your 1975 International 1300 4x4.

Please refer to QU40065 page for more details and ordering information.
Click to Enlarge

QU40066 Dana 60/61 Outer Axle Shaft to Spindle Thrust Washer is a genuine Dana Spicer part that fits on your Dana 60 or Dana 61 outer axle shaft to control thrust between the axle shaft and spindle.

Please refer to QU40066 page for more details and ordering information.
Click to enlarge

QU40148 Dana 60/61 Small Spindle V-Seal is a genuine Dana Spicer part that fits in the back of your spindle between QU40149 spindle bearing and QU40066 thrust washer in Model 60 or Model 61 open knuckle front drive axles on your 1975 IHC 1300 4x4.

Please refer to QU40148 page for more details and ordering information.
QU40149 Dana 50, Dana 60/61 Spindle Bearing is a genuine Dana Spicer original equipment part that is a press fit in the back of the spindle. This bearing is the primary support for your outer axle shaft.
Click to enlarge QK4740 Dana 60/61 6 Piece Large Spindle Seal and Thrust Washer Kit services BOTH sides of your 4x4 with two each of these parts: QU40065 Large Spindle V-seal, QU40066 Spindle Thrust Washer, and QU40148 Small Spindle V-seal.
Click to enlarge QU40168 Dana 60/61 Spindle Bearing and Seal Kit services ONE side of your 4x4 with one each of these parts: QU40065 Large Spindle V-seal, QU40066 Spindle Thrust Washer, QU40148 Small Spindle V-seal, and QU40149 Spindle Bearing.
Check Out Now
Steering Knuckles
     
     
     
     
     
     
     
     
     
Steering Linkage Parts
     
     
     
     
     
     
     
     
     
Tools
Having the right tool for the job makes the work easier and faster, plus the correct tool will usually minimize the chances of wrecking parts. We offer many special tools made specifically for the Dana 60 or Dana 61 front axle in your 1975 International 1300 4x4. Link to Vehicle Make or Category Links
QT5500 Wheel Bearing Packer takes the mess out of packing wheel bearings, plus it minimizes the chances of getting contaminants mixed with your wheel bearing grease. The QT5500 Bearing Packer does an absolutely beautiful job of forcing grease between the individual bearing rollers. The easiest and most efficient way to repack the front wheel bearings on your big IHC 1300!

TS4656 Adjustable Depth Type Inner Axle Shaft Seal Tool Set for 1975 International 4x4 trucks with either the Model 60 or Model 61 front axles.  Includes QT1042 Adjustable Depth Seal Installer, QT1133 Alloy Steel Press Screw with Hardware, & QT1130 Thrust Plate. Purchase QU40059 Axle Seals separately.

 

TS4867 Fixed Depth Type Inner Axle Shaft Seal Tool Set for 1975 International 1300 4x4s with either the Model 60 or Model 61 front axles. Includes QT1156 Fixed Depth Seal Installer, QT1133 Alloy Steel Press Screw with Hardware, & QT1130 Thrust Plate. Purchase QU40059 Axle Seals separately.
QT1133 Inner Axle Seal Press Screw Assembly for installing QU40059 Inner Axle Seals in Dana Model 60 and 61 front drive axles on 1975 IHC 4x4s.  Use with the QT1042 or QT1156 Seal Installers and QT1130 Thrust Plate. Also see TS4656 and TS4867 Inner Axle Seal Installer Tool Sets.
QT1042 Adjustable Depth Inner Axle Seal Installer Also see TS4656 Inner Axle Seal Installer Tool Set
QT1156 Fixed Depth Inner Axle Seal Installer Also see TS4867 Inner Axle Seal Installer Tool Set
QT1130 Thrust Plate Fits all Dana Model 60, Super 60, 61, and Closed Knuckle Model 70 axles from 1967-current. Also see TS4656 and TS4867 Inner Axle Seal Installer Tool Sets.
TS4862 Inner Axle Seal Remover Set is used to drive the QU40059 inner axle seals out of the axle housing bores on all 1975 International 4x4 Dana 60 or Dana 61 front axles. Set includes QT1145 Driver Handle, QT1151 Extension Rod, and QT1214 Seal Remover.
QT2005 Inner Pinion Bearing Installer is used to quickly and easily seat your QU50407 Inner Pinion Bearing on the pinion.
QT1805 Inner Pinion Bearing Cup Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer makes installing your QU50406 Inner Pinion Bearing Cup a simple and fast procedure.
QT1812 Outer Pinion Bearing Cup Installer Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer makes installing your QU50400 Outer Pinion Bearing Cup a simple and fast procedure.
QT1088 Differential Step Plate fits either side of the differential and is used to support the differential when installing your differential bearings or it acts as a push plate when you use a puller to remove the old bearings.
QT1158 Differential Bearing Installer makes a hard job easy. The raised inside ridge matches against inner differential bearing race allowing you to easily press or drive on QU50398 differential bearing until the bearing is fully seated against the differential adjusting shims.
QT1098 Differential Master Bearings slip on your differential in place of the taper bearings and cups. Used along with a dial indicator to determine the correct differential shim thickness.
QT1064 Dana 60 Upper King Pin Wrench removes and installs the upper king pin cones on 1975 IHC 1300 1 ton 4x4 trucks with Dana 60 front axles.
QT1218 2-9/16" Spindle Nut Socket for Hex Nuts
QT1100 Series Driver Handles are used in conjunction with our seal and bearing cup installers

QT1033 Case Spreader is used to relieve the differential bearing preload making it easy to safely remove and install your front differential without damaging expensive critical parts.

Please refer to QT1033 page for more details and ordering information.

QT1023 Triple Thread Spindle Puller Use with any 5/8" fine thread slide hammer to quickly and easily remove those rusted in front wheel bearing spindles on your IHC Dana 60 4x4 front axle without damage! Essential for servicing axle u-joints, king pins, spindle bearings, inner axle seals, and differentials on 1975 IHC 1300 heavy-duty 4x4s. Also works on most Dana 50IFS, Dana 44, Dana 30, Dana 27, and Dana 25 front axles.


QT1200 Tie Rod Separator allows you to remove the separate tie rod and drag link ends without wrecking the seals or screwing up your steering linkage ends.

QT9018 5 Pound Dead Blow Hammer is just about the first tool you will reach for to complete a multitude of jobs on your IHC 1300. From seating differentials to removing rusted on wheels, the ability to apply persuasive force without damaging the reluctant part will make you wonder how you ever lived without this essential tool.

Please refer to QT9018 page for more details and ordering information.

QT9302 5 Pound Slide Hammer a first-class tool for pulling just about anything you can get a matching 5/8" fine thread puller attachment for.

Please refer to QT9302 page for more details and ordering information.
QT1801 Outer Wheel Bearing Cup Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50411 Outer Wheel Bearing Cup a simple and fast procedure.
QT1804 Inner Wheel Bearing Cup Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50396 Inner Wheel Bearing Cup a simple and fast procedure.
Click to Enlarge QT1505 Wheel Seal Installer is custom made to quickly and easily install your new wheel seals without damaging them.
Check Out Now
Wheel Bearings and Seals (Individual)
IHC used only the best wheel bearings and seals money can buy to equip their Dana 60 and Dana 61 front axles to minimize the chance for warranty problems. That is why they chose Timken® Wheel Bearings and Spicer Wheel Seals for heavy-duty 1975 IHC 1300 4x4s using the big Danas. We supply those exact original equipment replacement Timken® Wheel Bearings and Spicer Wheel Seals to keep your IHC on the job for years to come. Link to Vehicle Make or Category Links
QU50411 Timken® Outer Wheel Bearing Cup for all 1975 IHC 1300 Dana 60 and Dana 61 front drive axles.
QU50412 Timken® Outer Wheel Bearing for all 1975 IHC 1300Dana 60 and Dana 61 front drive axles.
QU50396 Timken® Inner Wheel Bearing Cup for all 1975 IHC 1300 Dana 60 and Dana 61 front drive axles.
QU50398 Timken® Inner Wheel Bearing for all 1975 IHC 1300 Dana 60 and Dana 61 front drive axles.
QU40119 Inner Wheel Seal is a genuine Dana-Spicer original equipment replacement part for all 1975 IHC 1300 Dana 60 and Dana 61 front drive axles.
     
Check Out Now
Wheel Bearing and Seal Kits
IHC used the same wheel bearing and seal numbers for the entire 1975 to 1993 production run of Dana 60 and Dana 61 King Pin type front drive axles. However, spindle nut sets and lockout hubs will vary by year. Wheel hubs will vary by both year and if the truck had single or dual rear wheels. For 1975 to 1989, all the trucks used QU11070 hex spindle nuts, QU40051 spindle lock washer, and externally mounted drive flanges or lockout hubs using QU50216 hub gasket. 1990 and 1991 were transition years. During 1990, the external mount type wheel hub was phased out by an internally splined wheel hub, but the hex spindle nut configuration was retained for 1990 and most of the 1991 production. You may find some later 1991s with QK4729 round spindle nut set. For 1992 and 1993, the change over was complete. All trucks would have internally splined wheel hubs and use the round, QK4729 4 slot spindle nut set. We offer Wheel Bearing Part/Tool Kits with or without year specific Spindle Nut Wrenches and small parts.
Link to Vehicle Make or Category Links
Click to enlarge TK4744 Torque King® 1975-1993 Front Wheel Bearing and Seal Kit without Tools is a parts only (No Tools) complete front Wheel Bearing and Seal Kit for your heavy-duty IHC 1300 4x4 featuring Timken® Bearings and original equipment wheel seals for either the Dana Model 60 or 61 front axle. Kit includes two each of QU50411 Timken® Outer Wheel Bearing Cup, QU50412 Timken® Outer Wheel Bearing, QU50396 Timken® Inner Wheel Bearing Cup, QU50398 Timken® Inner Wheel Bearing, and QU40119 Wheel Seals.
TK4738 Torque King® 1975-1993 Front Wheel Bearing and Seal Kit with Install Tools for all 1975 IHC 1300 4x4 trucks with either the Dana Model 60 or 61 front axle. Kit includes QT1801 Cup Installer, QT1804 Inner Wheel Bearing Cup Installer, QT1505 Wheel Seal Installer, QT1100 Driver Handle, plus two each of QU50411 Timken® Outer Wheel Bearing Cup, QU50412 Timken® Outer Wheel Bearing, QU50396 Timken® Inner Wheel Bearing Cup, QU50398 Timken® Inner Wheel Bearing, and QU40119 Wheel Seals. This Kit DOES NOT INCLUDE Spindle Nut Socket or Hub Small Parts for your IHC!!!
Click to enlarge TK4725 Torque King® 1975-1990 Front Master Wheel Bearing and Seal Kit with Install Tools, Small Parts, and Spindle Nut Socket for 1975-1990 trucks with 8 bolt external mount hubs and hex spindle nuts. This would include 1975 IHC 1300 4x4 trucks with either the Dana Model 60 or 61 front axle, plus those 1990 models with external mount hubs. Kit includes QT1801 Cup Installer, QT1804 Inner Wheel Bearing Cup Installer, QT1505 Wheel Seal Installer, QT1100 Driver Handle QT1218 Hex Spindle Nut Socket, plus two each of QU40051 Spindle Lock Washer, QU50411 Timken® Outer Wheel Bearing Cup, QU50412 Timken® Outer Wheel Bearing, QU50396 Timken® Inner Wheel Bearing Cup, QU50398 Timken® Inner Wheel Bearing, QU40119 Wheel Seals, and QU50216 8 Bolt Hub Gasket.
$278 or Save 3% by purchasing Online for only $269.95


Click to enlarge TK4726 Torque King® 1975-1990 Front Master Wheel Bearing and Seal Kit with Install Tools and Small Parts for 1975-1990 trucks with 8 bolt external mount hubs and hex spindle nuts. This would include 1975 IHC 1300 4x4 trucks with either the Dana Model 60 or 61 front axle 4x4 trucks, plus those 1990 models with external mount hubs. Kit includes QT1801 Cup Installer, QT1804 Inner Wheel Bearing Cup Installer, QT1505 Wheel Seal Installer, QT1100 Driver Handle, plus two each of QU40051 Spindle Lock Washer, QU50411 Timken® Outer Wheel Bearing Cup, QU50412 Timken® Outer Wheel Bearing, QU50396 Timken® Inner Wheel Bearing Cup, QU50398 Timken® Inner Wheel Bearing, QU40119 Wheel Seals, and QU50216 8 Bolt Hub Gasket.
$231.77 or Save 3% by purchasing Online for only $224.95


TK4777 Torque King® 1990-1991 Front Master Wheel Bearing and Seal Kit with Install Tools, Small Parts, and Spindle Nut Socket for 1990-1991 trucks with internal mount splined hubs and hex spindle nuts. This would include most 1975 IHC 1300 4x4 trucks with either the Dana Model 60 or 61 front axles. Kit includes QT1801 Cup Installer, QT1804 Inner Wheel Bearing Cup Installer, QT1505 Wheel Seal Installer, QT1100 Driver Handle, QT1218 Hex Spindle Nut Socket, plus two each of QU40051 Spindle Lock Washer, QU50411 Timken® Outer Wheel Bearing Cup, QU50412 Timken® Outer Wheel Bearing, QU50396 Timken® Inner Wheel Bearing Cup, QU50398 Timken® Inner Wheel Bearing, QU40119 Wheel Seals, and QU50116 Quad-ring for Warn Hubs.
$278 or Save 3% by purchasing Online for only $269.95


TK4775 Torque King® 1990-1991 Front Master Wheel Bearing and Seal Kit with Install Tools and Small Parts for 1990-1991 trucks with internal mount splined hubs and hex spindle nuts. This would include most 1975 IHC 1300 4x4 trucks with either the Dana Model 60 or 61 front axles. Kit includes QT1801 Cup Installer, QT1804 Inner Wheel Bearing Cup Installer, QT1505 Wheel Seal Installer, QT1100 Driver Handle, plus two each of QU40051 Spindle Lock Washer, QU50411 Timken® Outer Wheel Bearing Cup, QU50412 Timken® Outer Wheel Bearing, QU50396 Timken® Inner Wheel Bearing Cup, QU50398 Timken® Inner Wheel Bearing, QU40119 Wheel Seals, and QU50116 Quad-ring for Warn Hubs.  
TK4736 Torque King® 1991-1993 Front Master Wheel Bearing and Seal Kit with Install Tools, Hub Quad-Rings, and Spindle Nut Socket for 1990-1991 trucks with internal mount splined hubs and round 4-slot spindle nuts. This would include most 1975 IHC 1300 4x4 trucks with either the Dana Model 60 or 61 front axles. Kit includes QT1801 Cup Installer, QT1804 Inner Wheel Bearing Cup Installer, QT1505 Wheel Seal Installer, QT1100 Driver Handle, QT1110 4 Tang Spindle Nut Socket, plus two each of QU50411 Timken® Outer Wheel Bearing Cup, QU50412 Timken® Outer Wheel Bearing, QU50396 Timken® Inner Wheel Bearing Cup, QU50398 Timken® Inner Wheel Bearing, QU40119 Wheel Seals, and QU50116 Quad-ring for Warn Hubs.
TK4737 Torque King® 1991-1993 Front Master Wheel Bearing and Seal Kit with Install Tools and Hub Quad-Rings for 1990-1991 trucks with internal mount splined hubs and round 4-slot spindle nuts. This would include most 1975 IHC 1300 4x4 trucks with either the Dana Model 60 or 61 front axles. Kit includes QT1801 Cup Installer, QT1804 Inner Wheel Bearing Cup Installer, QT1505 Wheel Seal Installer, QT1100 Driver Handle, plus two each of QU50411 Timken® Outer Wheel Bearing Cup, QU50412 Timken® Outer Wheel Bearing, QU50396 Timken® Inner Wheel Bearing Cup, QU50398 Timken® Inner Wheel Bearing, QU40119 Wheel Seals, and QU50116 Quad-ring for Warn Hubs.
     
 
Check Out Now