QK6000 Cummins Rear Crankshaft Seal Kit Quickly & easily replace that leaky rear crankshaft seal on your 1989-Current Cummins 5.9L or 6.7L Diesel engine without damaging the new seal!
No need to remove the flywheel housing or seal adapter! Includes CNC machined aluminum installer tool, guide studs, self tapping screws, drill bit, new Teflon lip seal with plastic seal starter, Threadlocker, anti-seize, and seal adapter centering guide. In addition to setting the seal square and to the correct depth, the installer can be used to press on crankshaft wear sleeves! Made in U.S.A.
Just need the tools? See
TS6000 Rear Crankshaft Installation Tool Kit.
Already have the Tools? Order
QU10556 Crank Seal with pilot and centering rings below.
Need Instructions or Torque Specs? See
TSB6000 Cummins Rear Crank Seal Replacement Tech Bulletin.
See Applications, Shopping Cart & Related Main Page Links Further Down This Page
Use Your Browser Back Arrow to Return to Previous Page
Dan the Gear Man Tech® Note 1:
With the QK6000 Kit there is absolutely no need to remove the flywheel housing and rear seal adapter. However if for any reason, you do need to remove the rear seal adapter from the back of the block, we do include a Cummins supplied stamped steel centering ring to center the rear seal adapter.
The centering ring is
required to center the seal adapter because Cummins did not dowel the seal retainer to the block so it can be installed off center unless you use the line up ring.
Dan the Gear Man Tech® Note 2:
The Seal Retainer is gasketed to both the back of the block and the top of the oil pan.
Dan the Gear Man Tech® Note 3:
Our Aluminum Crank Seal Installer will install both replacement seals and seals with wear sleeves to the correct depth on Cummins 4BT and 6BT Diesel engines. This includes Dodge trucks and most industrial, ag, marine, and automotive engines with 4BT and 6BT diesel engines.
Replaces Cummins crank seal installer tool 3824078.
Dan the Gear Man® Tech Note 4:
The thin plastic disposable Seal Starter is pre installed in the Seal. The Seal Starter is flared slightly to fit over the end of the crank. Once the Seal is slid over the Starter and onto the crank, remove and discard the Seal Starter.
Dan the Gear Man® Tech Note 5:
Related Parts and Tools for QK6000 Cummins Diesel Rear Crankshaft Seal Kit:
QU10523 Clutch Release Fork for 1989-1993 Cummins Diesel
QU10565 Clutch Release Fork for 1994-up Cummins Diesel
QU51002 Clutch Release Bearing Assembly for 1989-up Cummins Diesel
QU10558 Stock Needle Pilot Bearing for 1994-up Cummins Diesel
QU51010 Upgrade Ball Pilot Bearing for 1989-up Cummins Diesel
QK6007 Clutch Pivot Ball Kit for 1989-1993 Cummins Diesel
QK6005 Clutch Pivot Ball Kit for 1994-up Cummins Diesel
QK6008 Clutch Cover Bolt Kit for 1989-1993 with Sachs 13" original equipment type clutch
QK6010 Clutch Cover Bolt Kit for 1994-2004 5 Speed and 1999-2000 6 Speed (12.4" Clutch)
QK6015 Clutch Cover Bolt Kit for 2001-2005 6 Speed NV5600 Transmission (13" Clutch)
QK6009 Flywheel Bolt and Washer Kit for 1989-2005.5
QT3004 1-1/4"-10 Spline Clutch Alignment Tool for Dodge Diesel 5 Speed and 1999-2000 6 speed
QT3016 1-3/8"-10 Spline Clutch Alignment Tool for 2001-up 6 Speed
QT3001 Barring Tool for Dodge Cummins Diesel |
